| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 2S 513-1970 | 弹簧钢带材规范 | Specification for spring steel strip |
| BS 3S 500-1996 | 钢板和钢带检验、试验及验收程序 | Procedure for inspection, testing and acceptance of steel sheet and strip |
| BS 5S 100-1993 | 锻钢制品(钢板、薄钢板、钢带和钢管除外)检验、试验和验收程序 | Procedure for inspection, testing and acceptance of wrought steels (other than plate, sheet, strip and tube) |
| BS 7870-8.4-2003 | 配电和发电设施用低压(LV)和中等电压(MV)聚合绝缘电缆.地上和地下安装用多芯和多对电缆规范.具有降低火焰传 | LV and MV polymeric insulated cables for use by distribution and generation utilities - Specification for multicore and multipair cables for installation above and below ground - Single wire or double steel tape armoured and PVC sheathed multipair cable with copper conductors, having reduced fire propagation performance - Section 8.4 Single wire or double steel tape armoured and PVC sheathed multipair cable with copper conductors, having reduced fire propagation performance |
| BS 7870-8.6-2003 | 配电和发电设施用低压(LV)和中等电压(MV)聚合绝缘电缆.地上和地下安装用多芯和多对电缆规范.单丝或双钢带铠 | LV and MV polymeric insulated cables for use by distribution and generation utilities - Specification for multicore and multipair cables for installation above and below ground - Single wire or double steel tape armoured and non-halogenated sheathed multipair cable with copper conductors - Section 8.6 Single wire or double steel tape armoured and non-halogenated sheathed multipair cable with copper conductors |
| BS EN 10048-1997 | 热轧窄钢带.尺寸和形状公差 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| BS EN 10106-2007 | 经完全处理后交付的冷轧非定向电工钢片和钢带 | Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state |
| BS EN 10107-2005 | 加工完毕出厂的颗粒取向的电工钢片和钢带 | Grain-oriented electrical steel sheet and strip delivered in the fully processed state |
| BS EN 10140-2006 | 冷轧窄钢带.尺寸和形状公差 | Cold rolled narrow steel strip - Tolerances on dimensions and shape |
| BS EN 10143-2006 | 连续热浸涂覆的薄钢板和钢带.尺寸和形状公差 | Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
| BS EN 10151-2002 | 弹簧用不锈钢带材.交货技术条件 | Stainless steel strip for springs - Technical delivery conditions |
| BS EN 10251-1997 | 磁性材料.电工钢片和钢带几何特性值测定方法 | Magnetic materials - Methods of determination of the geometrical characteristics of electrical steel sheet and strip |
| BS EN 13246-2001 | 包装.捆扎钢带规范 | Packaging - Specification for tensional steel strapping |
| BS EN 523-2003 | 预应力钢筋用钢带材制钢筋鞘管.术语、要求和质量控制 | Steel strip sheaths for prestressing tendons - Terminology, requirements, quality control |
| BS EN 524-1-1997 | 预应力钢丝索用钢带护套.试验方法.形状及尺寸的测定 | Steel strip sheaths for prestressing tendons - Test methods - Determination of shape and dimensions |
| BS EN 524-2-1997 | 预应力钢丝索用钢带护套.试验方法.挠性的测定 | Steel strip sheaths for prestressing tendons - Test methods - Determination of flexural behaviour |
| BS EN 524-3-1997 | 预应力钢丝索用钢带护套.试验方法.反复弯曲试验 | Steel strip sheaths for prestressing tendons - Test methods - To-and-fro bending test |
| BS EN 524-4-1997 | 预应力钢丝索用钢带护套.试验方法 . 抗侧面负荷力的测定 | Steel strip sheaths for prestressing tendons - Test methods - Determination of lateral load resistance |
| BS EN 524-5-1997 | 预应力钢丝索用钢带护套.试验方法.抗拉负荷力的测定 | Steel strip sheaths for prestressing tendons - Test methods - Determination of tensile load resistance |
| BS EN 524-6-1997 | 预应力钢丝索用钢带护套.试验方法.密闭性的测定（水损失的测定） | Steel strip sheaths for prestressing tendons - Test methods - Determination of leaktightness (determination of water loss) |
| BS S 538-1975 | 铬-镍-钼-钒耐热钢薄板材和钢带规范(930-1130MPa:最大厚度6mm)(铬12、镍2.5、钼1.7、钒0.3) | Specification for chromium-nickel-molybdenum-vanadium heat-resisting steel sheet and strip (930-1130 MPa: maximum thickness 6 mm) (Cr 12, Ni 2.5, Mo 1.7, V 0.3) |
| 编号 | 中文名称 | 英文名称 |