| 编号 | 中文名称 | 英文名称 |
|---|
| IEC 60794-3-10-2002
| 光学纤维电缆.第3-10部分:户外电缆.管道光缆和直埋通信光缆的系列规范
| Optical fibre cables - Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables
|
| IEC 60794-3-12-2005
| 光缆.第3-12部分:室外电缆.房屋布线用管道和直埋通信光缆的详细规范
| Optical fibre cables - Part 3-12: Outdoor cables - Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling
|
| IEC 61084-1 AMD 1-1993
| 电气装置用电缆槽和管道系统 第1部分:一般要求 修改1
| Cable trunking and ducting systems for electrical installations; part 1: general requirements; amendment 1
|
| IEC 61084-1-1991
| 电气装置用电缆槽和管道系统 第1部分:一般要求
| Cable trunking and ducting systems for electrical installations; part 1: general requirements
|
| IEC 61084-2-1-1996
| 电气装置用电缆槽和管道系统 第2部分:特殊要求 第1节:安装在墙上或天花板上的电缆槽和管道系统
| Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 1: Cable trunking and ducting systems intended for mounting on walls or ceilings
|
| IEC 61084-2-2-2003
| 电气装置用电缆槽和管道系统.第2-2部分:特殊要求.安装在地板下和与地板齐平的设施用电缆槽和管道系统
| Cable trunking and ducting systems for electrical installations - Part 2-2: Particular requirements; Cable trunking systems and cable ducting systems intended for underfloor and flushfloor installations
|
| IEC 61084-2-4-1996
| 电气装置用电缆槽和管道系统 第2部分:特殊要求 第4节:接线柱
| Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 4: Service poles
|
| IEC 61400-21-2001
| 风轮发电机系统 第21部分：管道连接风轮机功率质量特性的测量和评定
| Wind turbine generator systems - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines
|
| ISO 10380-2003
| 管道系统.波纹状金属软管和软管配件
| Pipework - Corrugated metal hoses and hose assemblies
|
| ISO 10466-1997
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 耐初始环状变形可能性试验方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
|
| ISO 10467-2004
| 压力和无压力排水和排污塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统
| Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
|
| ISO 10472-3-1997
| 工业洗衣机安全要求 第3部分:管道式洗涤(联合)机及相关机械
| Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines
|
| ISO 10508-2006
| 冷热水装置用塑料管道系统.分类和设计指南
| Plastics piping systems for hot and cold water installations - Guidance for classification and design
|
| ISO 10639-2004
| 压力和无压力给水塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统
| Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
|
| ISO 10790-1999
| 封闭管道中流体流量的测量 科里奥利计选择、安装和使用指南(流量、密度和容量的测定)
| Measurement of fluid flow in closed conduits - Guidance to the selection, installation and use of Coriolis meters (mass flow, density and volume flow measurements)
|
| ISO 10802-1992
| 球墨铸铁管道 安装后水压试验
| Ductile iron pipelines; hydrostatic testing after installation
|
| ISO 10804-1-1996
| 球墨铸铁管道用减震连接系统 第1部分:设计规则和定型试验
| Restrained joint systems for ductile iron pipelines - Part 1: Design rules and type testing
|
| ISO 10806-2003
| 管道工程.波纹状金属软管用配件
| Pipework - Fittings for corrugated metal hoses
|
| ISO 10807-1994
| 管道工程 在爆燃性空气中电缆保护用皱纹软金属管组件
| Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres
|
| ISO 10838-1-2000
| 燃气用聚乙烯管道系统的机械式管件 第1部分:公称外径小于或等于63mm的管道用金属管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
| ISO 10838-2-2000
| 燃气用聚乙烯管道系统的机械式管件 第2部分:公称外径大于63mm的管道用金属管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
|
| ISO 10838-3-2001
| 燃气用聚乙烯管道系统的机械管件 第3部分：标称外径小于或等于63mm的热塑管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
| ISO 10928-1997
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材和管件 回归分析及其使用方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use
|
| ISO 10931-2005
| 工业用塑料管道系统.聚偏氟乙烯(PVDF).部件和系统的规范
| Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system
|
| ISO 10952-1999
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材和管件 在变形条件下断面内部耐化学腐蚀性的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition
|
| ISO 11563-2003
| 原油和石油制品.散货运输.实现管道满度的指南
| Crude petroleum and petroleum products - Bulk cargo transfer - Guidelines for achieving the fullness of pipelines
|
| ISO 11691-1995
| 声学 无气流管道消声器插入损失的测量 实验室测量法
| Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method
|
| ISO 13253-1995
| 管道式空调器和气-气加热泵 性能的检测和额定功率
| Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance
|
| ISO 13261-1-1998
| 空调和空气源热泵设备的声功率额定值 第1部分:无室外管道设备
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 1: Non-ducted outdoor equipment
|
| ISO 13261-2-1998
| 空调和空气源热泵设备的声功率额定值 第2部分:无室内管道设备
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 2: Non-ducted indoor equipment
|
| ISO 13359-1998
| 封闭管道中导电液体流量的测量 法兰电磁流量计 总长
| Measurement of conductive liquid flow in closed conduits - Flanged electromagnetic flowmeters - Overall length
|
| ISO 13623-2000
| 石油和天然气工业.管道输送系统
| Petroleum and natural gas industries - Pipeline transportation systems
|
| ISO 13628-5-2002
| 石油和天然气工业.水下采油系统的设计和操作.第5部分:水下缆线和管道
| Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals
|
| ISO 13678 Technical Corrigendum 1-2005
| 石油和天然气工业.对套管、管道和管线用的螺纹油的评定和试验.技术勘误1
| Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe; Technical Corrigendum 1
|
| ISO 13678-2000
| 石油和天然气工业 对套管、管道和管线用的螺纹绝缘膏的评价和试验
| Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe
|
| ISO 13703 Technical Corrigendum 1-2002
| 石油和天然气工业.近海生产平台上管道系统的设计和安装.技术勘误1
| Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms; Technical Corrigendum 1
|
| ISO 13703-2000
| 石油和天然气工业 海上开采平台上管道系统的设计和安装
| Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms
|
| ISO 13761-1996
| 塑料管材和管件 20℃以上使用的聚乙烯管道的压力折减系数
| Plastics pipes and fittings - Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 C
|
| ISO 13783-1997
| 塑料管道系统 硬聚氯乙烯(PVC-U)端部承受负荷的双承口连接件 密封和承受弯曲及内压的试验方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure
|
| ISO 13844-2000
| 塑料管道系统 用于硬聚氯乙烯管道的弹性密封环式承口连接件 负压下密封试验方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure
|
| ISO 13845-2000
| 塑料管道系统 用于硬聚氯乙烯管道的弹性密封环式承口连接件 内压下角度偏转密封试验方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection
|
| ISO 13846-2000
| 塑料管道系统 热塑性加压塑料管道用端部负载轴承和非端部负载轴承的安装和连接 在内水压下长期密封的试验方
| Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaklightness under internal water pressure
|
| ISO 13847 Technical Corrigendum 1-2001
| 石油和天然气工业.管道输送系统.管道焊接.技术勘误1
| Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines; Technical Corrigendum 1
|
| ISO 13847-2000
| 石油和天然气工业 管道输送系统 管道的焊接
| Petroleum and natural gas industrie - Pipeline transportation systems - Welding of pipelines
|
| ISO 13951-2001
| 塑料管道系统 聚烯烃管与管或管与管件之间的组件耐拉申负载试验方法
| Plastics piping systems - Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading
|
| ISO 13968-1997
| 塑料管道及导管系统 热塑性塑料管材 环揉性的测定
| Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility
|
| ISO 14164-1999
| 固定源排放 管道路气体流速的测定 自动监测方法
| Stationary source emissions - Determination of the volume flowrate of gas streams in ducts - Automated method
|
| ISO 14313-1999
| 石油和天然气工业 管道输送系统 管道阀
| Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves
|
| ISO 14511-2001
| 封闭管道中流体流量的测量 热质流量计
| Measurement of fluid flow in closed conduits - Thermal mass flowmeters
|
| ISO 14531-1-2002
| 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.第1部分:管
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels; Metric series; Specifications - Part 1: Pipes
|
| ISO 14531-2-2004
| 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.第2部分:热熔连接用配件
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 2: Fittings for heat-fusion jointing
|
| ISO 14531-3-2006
| 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.第3部分:机械连接用配件(包括PE-X/金属转
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 3: Fittings for mechanical jointing (including PE-X/metal transitions)
|
| ISO 14531-4-2006
| 塑料管道和配件.气体燃料运输用交联聚乙烯(PE-X)管道系统.米制系列.规范.第4部分:系统设计和安装指南
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 4: System design and installation guidelines
|
| ISO 14692-3-2002
| 石油和天然气工业.玻璃纤维增强塑料管.第3部分:系统管道
| Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System piping
|
| ISO 14723-2001
| 石油和天然气工业 管道输送系统 海底管道阀
| Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves
|
| ISO 14726-2-2002
| 船和造船技术.管道系统的内容的识别颜色.第2部分:中等差异和/或功能用补充颜色
| Ships and marine technology - Identification colours for the content of piping systems - Part 2: Additional colours for different media and/or functions
|
| ISO 15002-2000
| 医用气体管道系统终端装置用气流量测量装置
| Flow-metering devices for connection to terminal units of medical gas pipeline systems
|
| ISO 15306-2003
| 玻璃增强热固性塑料管道.抗周期性内压力的测定
| Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the resistance to cyclic internal pressure
|
| ISO 15348-2002
| 管道工程.金属波纹管膨胀节.总则
| Pipework - Metal bellows expansion joints - General
|
| ISO 15465-2004
| 管道.带绕金属软管和软管组件
| Pipework - Stripwound metal hoses and hose assemblies
|
| ISO 15493 Technical Corrigendum 1-2004
| 工业用塑料管道系统.丙烯腈-丁二烯-苯乙烯塑料(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元件
| Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series; Technical Corrigendum 1
|
| ISO 15493-2003
| 工业用塑料管道系统.丙烯腈-丁二烯-苯乙烯塑料(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元件
| Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and piping systems; Metric series
|
| ISO 15494-2003
| 工业用塑料管道系统.聚丁烯(PE)聚乙烯(PE)聚丙烯(PP).元件和系统的规范.米制系列
| Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the systems; Metric series
|
| ISO 15589-1-2003
| 石油和天然气工业.管道运输系统的阴极保护.第1部分:陆地管线
| Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 1: On-land pipelines
|
| ISO 15589-2-2004
| 石油和天然气工业.管道运输系统的阴极保护.第2部分:海上管线
| Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines
|
| ISO 15590-1-2001
| 石油和天然气工业 管道输送系统用诱导弯头、管件和法兰 第1部分：诱导弯头
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends
|
| ISO 15590-2-2003
| 石油和天然气工业.管道输送系统用进气弯管、管件和法兰.第2部分:管件
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings
|
| ISO 15590-3-2004
| 石油和天然气工业.管道输送系统用进气弯头、管件和法兰.第3部分:法兰
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges
|
| ISO 15649-2001
| 石油和天然气工业 管道
| Petroleum and natural gas industries - Piping
|
| ISO 15665 Technical Corrigendum 1-2004
| 声学.管道、阀门和法兰的隔音.技术勘误1
| Acoustics - Acoustic insulation for pipes, valves and flanges; Technical Corrigendum 1
|
| ISO 15749-2-2004
| 船舶和海上技术.船舶和海上结构物的排水系统.第2部分:重力系统用卫生排水和排水管道
| Ships and marine technology - Drainage systems on ships and marine structures - Part 2: Sanitary drainage, drain piping for gravity systems
|
| ISO 15749-3-2004
| 船舶和海上技术.船舶和海上结构物的排水系统.第3部分:真空系统用卫生排水和排水管道
| Ships and marine technology - Drainage systems on ships and marine structures - Part 3: Sanitary drainage, drain piping for vacuum systems
|
| ISO 15837-2004
| 船舶和海上技术.管道系统中使用的有垫圈机械联接件.性能规范
| Ships and marine technology - Gasketed mechanical couplings for use in piping systems - Performance specification
|
| ISO 15838-2003
| 船舶与海上技术.管道设施中使用的带密封衬垫的机械耦合配件.性能规范
| Ships and marine technology - Fittings for use with gasketed mechanical couplings used in piping applications - Performance specification
|
| ISO 15840-2004
| 船舶和海上技术.用于海上设备的热固性树脂纤维管道和装置的标准规范
| Ships and marine technology - Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
|
| ISO 15874-1-2003
| 冷热水装置用塑料管道系统.聚丙烯(PP).第1部分:总则
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General
|
| ISO 15874-2-2003
| 冷热水装置用塑料管道系统.聚丙烯(PP).第2部分:管
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes
|
| ISO 15874-3-2003
| 冷热水装置用塑料管道系统.聚丙烯(PP).第3部分:配件
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings
|
| ISO 15874-5-2003
| 冷热水装置用塑料管道系统.聚丙烯(PP).第5部分:系统的适用性
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system
|
| ISO 15875-1-2003
| 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第1部分:总则
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General
|
| ISO 15875-2-2003
| 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第2部分:管道
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes
|
| ISO 15875-3-2003
| 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第3部分:配件
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings
|
| ISO 15875-5-2003
| 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第5部分:系统的适用性
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system
|
| ISO 15876-1-2003
| 冷热水装置用塑料管道系统.聚丁烯(PB).第1部分:总则
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General
|
| ISO 15876-2-2003
| 冷热水装置用塑料管道系统.聚丁烯(PB).第2部分:管道
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes
|
| ISO 15876-3-2003
| 冷热水装置用塑料管道系统.聚丁烯(PB).第3部分:配件
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings
|
| ISO 15876-5-2003
| 冷热水装置用塑料管道系统.聚丁烯(PB).第5部分:系统的适用性
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system
|
| ISO 15877-1-2003
| 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第1部分:总则
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General
|
| ISO 15877-2-2003
| 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第2部分:管道
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes
|
| ISO 15877-3-2003
| 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第3部分:配件
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings
|
| ISO 15877-5-2003
| 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第5部分:系统的适用性
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system
|
| ISO 15908-2002
| 热塑性管道系统用胶粘剂.胶粘剂热稳定性测定的试验方法
| Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives
|
| ISO 16422-2006
| 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于压力下水运输的管道和接头.规范
| Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications
|
| ISO 16708-2006
| 石油和天然气工业.管道传输系统.基于可靠性的极限状态法
| Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods
|
| ISO 16871-2003
| 塑料管道系统.塑料管道和配件.自然风化法
| Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering
|
| ISO 17454-2006
| 塑料管道系统.多层管道.用牵引装置测试不同层粘性的试验方法
| Plastics piping systems - Multilayer pipes - Test method for the adhesion of the different layers using a pulling rig
|
| ISO 17455-2005
| 塑料管道系统.多层管道.屏蔽管道的透氧性测定
| Plastics piping systems - Multilayer pipes - Determination of the oxygen permeability of the barrier pipe
|
| ISO 19220-2004
| 建筑物内土壤和废物排放(低温和高温)用塑料管道系统.苯乙烯共聚物混合料(SAN + PVC)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Styrene copolymer blends (SAN + PVC)
|
| ISO 19921-2005
| 船舶和海上技术.带弹性密封件的金属管道部件的耐火性.试验方法
| Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Test methods
|
| ISO 19922-2005
| 船舶和海上技术.带弹性密封件的金属管道部件的耐火性.试验台要求
| Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Requirements imposed on the test bench
|
| ISO 21329-2004
| 石油和天然气工业.管道运输系统.机械连接器的试验过程
| Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors
|
| ISO 2186-1973
| 封闭管道中的流体流量 用于一次和二次元件间压力信号传输的连接法
| Fluid flow in closed conduits; Connections for pressure signal transmissions between primary and secondary elements
|
| ISO 24033-2006
| 耐升温的聚乙烯管道(PE-RT).时间和温度对预期强度的影响
| Pipes made of raised-temperature-resistance polyethylene (PE-RT) - Effect of time and temperature on the expected strength
|
| ISO 2975-1-1974
| 封闭管道中水流量的测量 示踪法 第1部分:总则
| Measurement of water flow in closed conduits; Tracer methods; Part I : General
|
| ISO 2975-2-1975
| 封闭管道中水流量的测量 示踪法 第2部分:用非放射性示踪剂的恒速注入法
| Measurement of water flow in closed conduits; Tracer methods; Part II : Constant rate injection method using non-radioactive tracers
|
| ISO 2975-3-1976
| 封闭管道中水流量的测量 示踪法 第3部分:用放射性示踪剂的恒速注入法
| Measurement of water flow in closed conduits; Tracer methods; Part III : Constant rate injection method using radioactive tracers
|
| ISO 2975-6-1977
| 封闭管道中水流量的测量 示踪法 第6部分:用非放射性示踪剂的传输时间法
| Measurement of water flow in closed conduits; Tracer methods; Part VI : Transit time method using non-radioactive tracers
|
| ISO 2975-7-1977
| 封闭管道中水流量的测量 示踪法 第7部分:用放射性示踪剂的传输时间法
| Measurement of water flow in closed conduits; Tracer methods; Part VII : Transit time method using radioactive tracers
|
| ISO 3126-2005
| 塑料管道系统.塑料部件.尺寸测定
| Plastics piping systems - Plastics components - Determination of dimensions
|
| ISO 3183-1-1996
| 石油和天然气工业 管道钢管 交货技术条件 第1部分:A级钢管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 1: Pipes of requirement class A
|
| ISO 3183-2-1996
| 石油和天然气工业 管道钢管 交货技术条件 第2部分:B级钢管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 2: Pipes of requirements class B
|
| ISO 3183-3 Technical Corrigendum 1-2000
| 石油和天然气工业 管道钢管 交货技术条件 第3部分:C级钢管的要求 技术勘误1
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C - Technical Corrigendum 1
|
| ISO 3183-3-1999
| 石油和天然气工业 管道钢管 交货技术条件 第3部分:C级钢管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C
|
| ISO 3586-1976
| 玻璃设备、管道和配件 试验、管理和使用的一般规则
| Glass plant, pipeline and fittings; general rules for testing, handling and use
|
| ISO 3587-1976
| 玻璃设备、管道和配件 公称内径15mm～150mm的管道和配件 通用性和互换性
| Glass plant, pipeline and fittings; Pipeline and fittings of nominal bore 15 to 150 mm; Compatibility and interchangeability
|
| ISO 3633-2002
| 建筑物内污废水排放系统用硬聚氯乙烯(PVC-U)塑料管道系统(低温和高温)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U)
|
| ISO 4006-1991
| 封闭管道中流体流量的测量 词汇和符号 两种语言版
| Measurement of fluid flow in closed conduits; vocabulary and symbols
|
| ISO 4059-1978
| 聚乙烯(PE)管材 机械式管道连接系统压降 试验方法和要求
| Polyethylene (PE) pipes; Pressure drop in mechanical pipe-jointing systems; Method of test and requirements
|
| ISO 4144-2003
| 管道系统.符合ISO 7/1螺纹标准的不锈钢配件
| Pipework - Stainless steel fittings threaded in accordance with ISO 7-1
|
| ISO 4179-2005
| 压力和非压力管道用球墨铸铁管和配件.水泥灰浆内衬
| Ductile iron pipes and fittings for pressure and non-pressure pipelines - Cement mortar lining
|
| ISO 4185 Technical Corrigendum 1-1993
| 封闭管道中液体流量的测量 重量法 技术勘误1
| Measurement of liquid flow in closed conduits; weighing method; technical corrigendum 1
|
| ISO 4185-1980
| 封闭管道中液体流量的测量 重量法
| Measurement of liquid flow in closed conduits; Weighing method
|
| ISO 4435-2003
| 地下排水和排污水用塑料管道系统.未增塑聚氯乙烯
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U)
|
| ISO 4633-2002
| 橡胶密封.供水、排水和污水管道用密封圈.材料规范
| Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials
|
| ISO 4704-1977
| 玻璃设备、管道和配件 玻璃设备元件
| Glass plant, pipeline and fittings; Glass plant components
|
| ISO 5136-2003
| 声学.风机和其他风动设备辐射入管道中的声功率的测定.管道法
| Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method
|
| ISO 5167-1 Technical Corrigendum 1-1997
| 用压差装置测量流体流量 第1部分:圆截面管道中插入的节流孔板、喷嘴和文杜利管 技术勘误1
| Measurement of fluid flow by means of pressure differential devices - Part 1: Orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full - Technical Corrigendum 1
|
| ISO 5167-1-2003
| 用插入圆截面管道中的压差装置测量流体流量.第1部分:一般原理和要求
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements
|
| ISO 5167-2-2003
| 用插入圆截面管道中的压差装置测量流体流量.第2部分:节流孔板
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates
|
| ISO 5167-3-2003
| 用插入圆截面管道中的压差装置测量流体流量.第3部分:喷嘴和文杜利喷嘴
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles
|
| ISO 5167-4-2003
| 用插入圆截面管道中的压差装置测量流体流量.第4部分:文杜利管
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes
|
| ISO 5176-1-1991
| 用压差装置测量流体流量.第1部分:圆截面管道中插入的节流孔板、喷嘴和文杜利管
| Measurement of fluid flow by means of pressure differential devices; part 1: orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full
|
| ISO 5667-5-2006
| 水质.采样.第5部分:从水处理站和管道分配系统采样饮用水的指南
| Water quality - Sampling - Part 5: Guidance on sampling of drinking water from treatment works and piped distribution systems
|
| ISO 5752-1982
| 法兰连接的管道系统用金属法兰 结构长度和端面至中心的尺寸
| Metal valves for use in flanged pipe systems; Face-to-face and centre-to-face dimensions
|
| ISO 580-2005
| 塑料管和管道系统.喷射铸造热塑配件.热效应直观评估法
| Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating
|
| ISO 6412-1-1989
| 技术制图 管道的简化表示法 第1部分:通则和正交表示法
| Technical drawings; simplified representation of pipelines; part 1: general rules and orthogonal representation
|
| ISO 6412-2-1989
| 技术制图 管道的简化表示法 第2部分:等角投影
| Technical drawings; simplified representation of pipelines; part 2: isometric projection
|
| ISO 6412-3-1993
| 技术制图 管道的简化表示法 第3部分:通风和排放系统终端部件
| Technical drawings; simplified representation of pipelines; part 3: terminal features of ventilation and drainage systems
|
| ISO 6448-1985
| 橡胶密封件 输送石油产品管道和配件用密封圈 材料规范
| Rubber seals; Joint rings used for petroleum product supply pipes and fittings; Specification for material
|
| ISO 6773-1994
| 航空航天 流体系统 管道及配件的热冲击试验
| Aerospace - Fluid systems - Thermal shock testing of piping and fittings
|
| ISO 6817-1992
| 封闭管道中导电液体流量的测量 采用电磁流率计的方法
| Measurement of conductive liquid flow in closed conduits; method using electromagnetic flowmeters
|
| ISO 6944-1985
| 耐火试验 通风管道
| Fire resistance tests; Ventilation ducts
|
| ISO 7235-2003
| 声学.管道消音器和空气界面装置的实验室测量步骤.插入损失、流动噪声和总压损失
| Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss
|
| ISO 7268 AMD 1-1984
| 管道元件 公称压力的定义 修改1
| Amendment 1-1984
|
| ISO 7268-1983
| 管道元件 公称压力的定义
| Pipe components; Definition of nominal pressure
|
| ISO 7278-2-1988
| 液态烃 动态测量 计量校正系统 第2部分:管道校准
| Liquid hydrocarbons; dynamic measurement; proving systems for volumetric meters; part 2: pipe provers
|
| ISO 7278-4-1999
| 液态烃 动态测量 计量校正系统 第4部分:管道校正仪操作导则
| Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 4: Guide for operators of pipe provers
|
| ISO 7369-2004
| 管道工程.金属软管和软管组件.词汇
| Pipework - Metal hoses and hose assemblies - Vocabulary
|
| ISO 7396-1-2002
| 医用燃气管道系统.第1部分:医用压缩气体和真空管道
| Medical gas pipeline systems - Part 1: Pipelines for compressed medical gases and vacuum
|
| ISO 7396-2-2000
| 医用气体管道系统 第2部分:麻醉用气体净化处理系统
| Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems
|
| ISO 7432-2002
| 玻璃纤维增强热固性塑料管道和管配件.检验设计带弹性体密封件的锁紧套筒连接件,包括双插孔连接件的试验方法
| Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
|
| ISO 7509-2000
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 持续内压力下破坏时间的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of time to failure under sustained internal pressure
|
| ISO 7510-1997
| 塑料管道系统 玻璃纤维增强塑料(GRP)元件 重量法测定成分
| Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents using the gravimetric method
|
| ISO 7511-1999
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材和管件 确定短期内压下管壁密封性的检验方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure
|
| ISO 7671-2003
| 建筑物内污、废水排放(低温和高温)用塑料管道系统.聚丙烯(PP)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
|
| ISO 7675-2003
| 建筑物内污、废水(低温和高温)排放用塑料管道系统.氯化聚氯乙烯
| Plastic piping systems for soil and waste discharge (low and high temperature) inside buildings - Chlorinated poly(vinyl chloride) (PVC-C)
|
| ISO 7682-2003
| 建筑物内污、废水排放(低温和高温)用塑料管道系统.丙烯腈-丁二烯-苯乙烯(ABS)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS)
|
| ISO 7684-1997
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 干燥条件下蠕变系数的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions
|
| ISO 7685-1998
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 初始有效环刚度的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
|
| ISO 8277-1988
| 造船 管道系统 信息传递
| Shipbuilding; pipework; information transfer
|
| ISO 8316-1987
| 封闭管道中液体流量的测量 采用在容积计量容器内收集液体的方法
| Measurement of liquid flow in closed conduits; Method by collection of the liquid in a volumetric tank
|
| ISO 8513-2000
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 纵向抗拉特性的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of longitudinal tensile properties
|
| ISO 8521-1998
| 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 表面内周拉伸强度的测定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
|
| ISO 8770-2003
| 建筑物内污、废水排放(低温和高温)用塑料管道系统.聚乙烯(PE)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE)
|
| ISO 8795-2001
| 输送人类生活用水用塑料管道系统 流动评定 塑料管道和管件及其接头的流动值的测定
| Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints
|
| ISO 9080-2003
| 塑料管道和导管系统.用外推法测定热塑性塑料管材的长期静液压强度
| Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
|
| ISO 9104-1991
| 封闭管道中流体流量的测量 液体电磁流量计性能评定方法
| Measurement of fluid flow on closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids
|
| ISO 9170-1-1999
| 医用气体管道系统用终端设备 第1部分:供压缩医用设备和真空用的终端设备
| Terminal units for medical gas pipeline systems - Part 1: Terminal units for use with compressed medical gases and vacuum
|
| ISO 9170-2-1999
| 医用气体管道系统用终端设备 第2部分:麻醉气体清除系统用的终端设备
| Terminal units for medical gas pipeline systems - Part 2: Terminal units for anaesthetic gas scavenging systems
|
| ISO 9311-1-2005
| 热塑性管道系统用胶粘剂.第1部分:膜层特性的测定
| Adhesives for thermoplastic piping systems - Part 1: Determination of film properties
|
| ISO 9311-2-2002
| 热塑管道系统的胶粘剂.第2部分:剪切强度的测定
| Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength
|
| ISO 9311-3-2005
| 热塑性管道系统用胶粘剂.第3部分:测定耐内压力性的试验方法
| Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure
|
| ISO 9349-2004
| 预绝缘球墨铸铁管道系统
| Preinsulated ductile iron pipeline systems
|
| ISO 9368-1-1990
| 采用称重法测量封闭管道中液体的流量 校核装置的规程 第1部分:静态称量系统
| Measurement of liquid flow in closed conduits by the weighing method; procedures for checking installations; part 1: static weighing systems
|
| ISO 9398-3-2003
| 工业洗衣机规范.容量和能耗特性定义和测试.第3部分:管道式洗涤机
| Specifications for industrial laundry machines - Definitions and testing of capacity and consumption characteristics - Part 3: Washing tunnels
|
| ISO 9631-2003
| 橡胶密封件.温度为110℃及以下的热水供给管道用密封圈.材料规范
| Rubber seals - Joint rings for pipelines for hot-water supply up to 110 degrees C - Specification for the material
|
| ISO 9803-1993
| 真空技术 管道配件 装配尺寸
| Vacuum technology; pipeline fittings; mounting dimensions
|
| ISO 9853-1991
| 压力管道系统用硬聚氯乙烯(PVC-U)管件 扁平试验
| Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems; crushing test
|
| ISO 9951 Technical Corrigendum 1-1994
| 封闭管道中气体流量的测量 技术勘误1
| Measurement of gas flow in closed conduits - Turbine meters; Technical Corrigendum 1
|
| ISO 9951-1993
| 封闭管道中气体流量的测量 涡轮计
| Measurement of glas flow in closed conduits; turbine meters
|
| ISO/TR 11295-1992
| 用塑料管材和管件对管道系统的修复技术
| Techniques for rehabilitation of pipeline systems by the use of plastics pipes and fittings
|
| ISO/TR 12764-1997
| 封闭管道中流体流量的测量 在旋转圆截面导管中插入涡流流量计来测量流率
| Measurement of fluid flow in closed conduits - Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full
|
| ISO/TR 3313-1998
| 封闭管道中流体流量的测量 流体脉动对流量测量仪器影响的指南
| Measurement of fluid flow in closed conduits - Guidelines on the effects of flow pulsations on flow-measurement instruments
|
| ISO/TR 9824-1-1990
| 封闭管道的自由水面流测量 第1部分:测量方法
| Measurement of free surface flow in closed conduits; part 1: methods
|
| ISO/TR 9824-2-1990
| 封闭管道的自由水面流测量 第2部分:测量设备
| Measurement of free surface flow in closed conduits; part 2: equipment
|
| ISO/TS 15874-7-2003
| 冷热水装置用塑料管道系统.聚丙烯(PP).第7部分:合格评定指南
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15875-7-2003
| 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第7部分:合格评定指南
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15876-7-2003
| 冷热水装置用塑料管道系统.聚丁烯(PB).第7部分:合格评定指南
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15877-7-2003
| 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第7部分:合格评定指南
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 7024-2005
| 建筑物内污水废水排放用塑料管道系统(低温和高温).热塑塑料.推荐的安装规范
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Thermoplastics - Recommended practice for installation
|
| 编号 | 中文名称 | 英文名称 |
|---|