| 编号 | 中文名称 | 英文名称 |
|---|
| DL/T 695-1999
| 电站钢制对焊管件
| ()
|
| DL/T 935-2005
| 钢塑复合管和管件
| ()
|
| GB 15558.2-2005
| 燃气用埋地聚乙烯(PE)管道系统第2部分:管件
| Buried Polyethylene(PE)piping systems for the supply of gaseous fuels Part 2:Fittings
|
| GB/T 12459-2005
| 钢制对焊无缝管件
| Steel butt-welding seamless pipe fittings
|
| GB/T 12772-1999
| 排水用柔性接口铸铁管及管件
| Cast iron pipes and fittings with flexible joint sewerage
|
| GB/T 13021-1991
| 聚乙烯管材和管件炭黑含量的测定热失重法
| Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis
|
| GB/T 13295-2003
| 水及燃气管道用球墨铸铁管、管件和附件
| Ductile iron pipes，fittings and accessories for water or gas applications
|
| GB/T 13401-2005
| 钢板制对焊管件
| Steel plate butt-welding pipe fittings
|
| GB/T 13663.2-2005
| 给水用聚乙烯(PE)管道系统第2部分:管件
| Polyethylene(PE)pipings systems for water supply Part 2:Fittings
|
| GB/T 14383-1993
| 锻钢制承插焊管件
| Forged steel socket welding pipe fittings
|
| GB/T 14626-1993
| 锻钢制螺纹管件
| Forged steel threaded pipe fittings
|
| GB/T 15819-2006
| 灌溉用聚乙烯(PE)管材由插入式管件引起环境应力开裂敏感性的试验方法和技术要求
| Polyethylene (PE) pipes for irrigation laterals - Susceptibility to envionmental stress cracking induced by insert-type fittings - Test method and specification
|
| GB/T 15820-1995
| 聚乙烯压力管材与管件连接的耐拉拔试验
| Test of resistance to pull out ofjoints between polyethylene (PE) pressure pipes and fittings
|
| GB/T 17185-1997
| 钢制法兰管件
| Steel pipe fittings for flanged joint
|
| GB/T 17241.1-1998
| 铸铁管法兰类型
| Synoptic table for cast iron pipe flanges
|
| GB/T 17241.2-1998
| 铸铁管法兰盖
| Cast iron pipe blank flanges
|
| GB/T 17241.3-1998
| 带颈螺纹铸铁管法兰
| Hubbed threaded cast iron pipe flanges
|
| GB/T 17241.4-1998
| 带颈平焊和带颈承插焊铸铁管法兰
| Hubbed slip-on-welding and hubbed socket welding cast iron pipe flanges
|
| GB/T 17241.5-1998
| 管端翻边带颈松套铸铁管法兰
| Loose hubbed cast iron pipe flanges for lapped pipe end
|
| GB/T 17241.6-1998
| 整体铸铁管法兰
| Integral cast iron pipe flanges
|
| GB/T 17241.7-1998
| 铸铁管法兰技术条件
| Specifications for cast iron pipe flanges
|
| GB/T 17391-1998
| 聚乙烯管材与管件热稳定性试验方法
| Test method for thermal stability of polyethylene pipes and fittings
|
| GB/T 17456-1998
| 球墨铸铁管外表面喷锌涂层
| Ductile iron pipes--External zinc-spray coating
|
| GB/T 17457-1998
| 球墨铸铁管水泥砂浆离心法衬层一般要求
| Ductile iron pipes--Centrifugal cement mortar lining--General requirements
|
| GB/T 17458-1998
| 球墨铸铁管水泥砂浆离心法衬层新拌砂浆的成分检验
| Ductile iron pipes--Centrifugal cement mortar lining--Composition controls of freshly appliedmortar
|
| GB/T 17459-1998
| 球墨铸铁管沥青涂层
| Ductile iron pipes--Bitumen coating
|
| GB/T 18251-2000
| 聚烯烃管材、管件和混配料中颜料或炭黑分散的测定方法
| Method for the assessment of pigment or carbon black dispersion in polyolefin pipes，fittings and compounds
|
| GB/T 18474-2001
| 交联聚乙烯(PE-X)管材与管件交联度的试验方法
| Pipes and fittings made of crosslinked polyethylene(PE-X)--Estimation of the degree of crosslinkingby determination of the gel content
|
| GB/T 18475-2001
| 热塑性塑料压力管材和管件用材料分级和命名总体使用(设计)系数
| Thermoplastics materials for pipes and fittings for pressure applications classification and designation--Overall service(design) coefficient
|
| GB/T 18742.3-2002
| 冷热水用聚丙烯管道系统第3部分:管件
| Polypropylene piping systems for hot and cold water installations--Part 3:Fittings
|
| GB/T 18991-2003
| 冷热水系统用热塑性塑料管材和管件
| Thermoplastics pipes and fittings forhot and cold water systems
|
| GB/T 18993.3-2003
| 冷热水用氯化聚氯乙烯(PVC-C)管道系统第3部分: 管件
| Chlorinated poly(Vinyl chloride) piping systems for hot and cold water installations--Part 3: Fittings
|
| GB/T 18998.3-2003
| 工业用氯化聚氯乙烯(PVC-C)管道系统第3部分: 管件
| Chlorinated poly(vinyl chloride)(PVC-C) piping systems for industrial applications--Part 3: Fittings
|
| GB/T 19228.1-2003
| 不锈钢卡压式管件
| Stainless steel press-fittings
|
| GB/T 19228.2-2003
| 不锈钢卡压式管件连接用薄壁不锈钢管
| Light gauge stainless steel pipes for stainless steel press-fittings
|
| GB/T 19228.3-2003
| 不锈钢卡压式管件用橡胶O形密封圈
| O-rings for stainless steel press-fittings
|
| GB/T 19278-2003
| 热塑性塑料管材、管件及阀门通用术语及其定义
| General terms and their definitions of thermoplastic pipes，fittings and valves
|
| GB/T 19473.3-2004
| 冷热水用聚丁烯(PB)管道系统第3部分:管件
| Polybutylene(PB) piping systems for hot and cold water installations--Part 3:Fittings
|
| GB/T 19712-2005
| 塑料管材和管件聚乙烯(PE)鞍形旁通抗冲击试验方法
| Plastics pipes and fittingsPolyethylene(PE) tapping tees Test method for impact resistance
|
| GB/T 19806-2005
| 塑料管材和管件聚乙烯电熔组件的挤压剥离试验
| Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies
|
| GB/T 19807-2005
| 塑料管材和管件聚乙烯管材和电熔管件组合试件的制备
| Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
|
| GB/T 19808-2005
| 塑料管材和管件公称外径大于或等于90mm的聚乙烯电熔组件的拉伸剥离试验
| Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
| GB/T 19809-2005
| 塑料管材和管件聚乙烯(PE)管材/管材或管材/管件热熔对接组件的制备
| Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
|
| GB/T 19810-2005
| 聚乙烯(PE)管材和管件热熔对接接头拉伸强度和破坏形式的测定
| Polyethylene(PE)pipe and fittings-Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
| GB/T 19993-2005
| 冷热水用热塑性塑料管道系统 管材管件组合系统热循环试验方法
| Thermoplastics piping systems for hot and cold water supply-Test method for the resiance of pipes and fittings mounted assemblies to thermal cycling
|
| GB/T 20201-2006
| 灌溉用聚乙烯(PE)压力管机械连接管件
| Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes
|
| GB/T 20207.2-2006
| 丙烯腈－丁二烯－苯乙烯（ABS）压力管道系统第2部分：管件
| Acrylonitrile-butadiene-styrene (ABS) pressure piping systems - Part 2: fittings
|
| GB/T 20674.1-2006
| 塑料管材和管件 聚乙烯系统熔接设备 第1部分：热熔对接
| Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1：Butt fusion
|
| GB/T 20674.2-2006
| 塑料管材和管件 聚乙烯系统熔接设备 第2部分：电熔连接
| Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion
|
| GB/T 3287-2000
| 可锻铸铁管路连接件
| Malleable cast iron pipe fittings
|
| GB/T 3420-1982
| 灰口铸铁管件
| Gray iron castigs for pipe fittings
|
| GB/T 3422-1982
| 连续铸铁管
| Cast-iron pressure pipe made by continuous casting process
|
| GB/T 5836.2-2006
| 建筑排水用硬聚氯乙烯（PVC-U）管件
| Unplasticized poly(vinyl chloride) (PVC-U) fittings for soil and waste inside buildings
|
| GB/T 6483-1986
| 柔性机械接口灰口铸铁管
| Soft mechanical joint grey cast iron pipe
|
| GB/T 6567.3-1986
| 管路系统的图形符号管件
| Graphical symbols for piping systems--Piping accessories
|
| GB/T 6567.5-2003
| 管路系统的图形符号管路、管件和阀门等图形符号的轴测图画法
| Graphical symbols for piping systems--Axonometric representation of graphical symbols for piping，piping accessories and valves etc
|
| GB/T 8714-1988
| 梯唇型橡胶圈接口铸铁管
| Grey cast iron pipes with rubber ring of ladder-lip-shaped
|
| GB/T 8715-1988
| 柔性机械接口铸铁管件
| Soft mechanical joint grey cast iron fittings
|
| GB/T 8801-1988
| 硬聚氯乙烯 (PVC-U) 管件坠落试验方法
| Test method for unplasticized (PVC-U) fittings by falling
|
| GB/T 8802-2001
| 热塑性塑料管材、管件维卡软化温度的测定
| Thermoplastics pipes and fitting--Determination of vicat softening temperature
|
| GB/T 8803-2001
| 注射成型硬质聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)、丙烯腈-丁二烯-苯乙烯三元共聚物(ABS)和丙烯腈-苯乙烯
| Injection-moulded unplasticized poly(vinyl chloride)(PVC-U)，chlorinated poly(vinyl chloride)(PVC-C)，acrylonitrile butadiene-styrene(ABS)and acrylonitrile-styrene-acrylester(ASA)fittings--Hot oven test method
|
| HG/T 20538-1992
| 衬塑（PP、PE、PVC）钢管和管件
| ()
|
| HG/T 20539-1992
| 增强聚丙烯（FRPP）管子和管件
| ()
|
| HG/T 2128-1991
| 耐酸酚醛塑料制化工设备、管、管件技术条件
| ()
|
| HG/T 21501-1993
| 衬胶钢管和管件
| ()
|
| HG/T 21561-1994
| 丙烯腈—丁二烯—苯乙烯（ABS）管和管件
| ()
|
| HG/T 21562-1994
| 衬聚四氟乙烯钢管和管件
| ()
|
| HG/T 21579-1995
| 聚丙烯/玻璃钢（PP/FRP）复合管及管件
| ()
|
| HG/T 21631-1990
| 钢制有缝对焊管件
| ()
|
| HG/T 21633-1991
| 玻璃钢管和管件
| ()
|
| HG/T 21634-1988
| 锻钢承插焊管件
| ()
|
| HG/T 21635-1987
| 碳钢、低合金钢无缝对焊管件
| ()
|
| HG/T 21636-1987
| 玻璃钢/聚氯乙烯（FRP/PVC)复合管和管件
| ()
|
| HG/T 2435-1993
| 玻璃管和管件
| ()
|
| HG/T 2436-1993
| 玻璃管和管件耐压试验方法
| ()
|
| HG/T 2437-2006
| 塑料衬里复合钢管和管件
| Steel pipes and fitting lined with plastic
|
| HG/T 3691-2001
| 工业用钢骨架聚乙稀塑料复合管件
| ()
|
| HG/T 3705-2003
| 金属网聚四氟乙烯复合管与管件
| ()
|
| HG/T 3707-2003
| 工业用孔网钢骨架聚乙烯复合管件
| ()
|
| HG/T 3731-2004
| 玻璃纤维增强聚氯乙烯复合管和管件
| ()
|
| JB/T 1308.2-1999
| PN250MPa阀门、管件和紧固件技术条件
| ()
|
| JB/T 2768-1992
| PN16.0～32.0MPa 管子、管件、阀门端部尺寸
| ()
|
| JB/T 2778-1992
| PN16.0～32.0MPa 管件和紧固件温度标记
| ()
|
| JB/T 450-1992
| PN16.0～32.0MPa 锻造角式高压阀门、管件、紧固件 技术条件
| ()
|
| JB/T 5976.1-1992
| PNO.6MPa可锻铸铁管法兰盖
| ()
|
| JB/T 5976.2-1992
| PN1.0MPa可锻铸铁管法兰盖
| ()
|
| JB/T 5976.3-1992
| PN1.6MPa可锻铸铁管法兰盖
| ()
|
| JB/T 5976.4-1992
| PN2.5MPa可锻铸铁管法兰盖
| ()
|
| JB/T 5976.5-1992
| PN4.0MPa可锻铸铁管法兰盖
| ()
|
| JB/T 5982-1992
| 可锻铸铁管法兰用石棉橡胶垫片
| ()
|
| JB/T 6308-2000
| 离心铸管机 技术条件
| ()
|
| JB/T 7525-1994
| 聚丙烯 玻璃纤维增强塑料复合管和管件
| ()
|
| JB/T 7870-1997
| 喷灌用金属薄壁管及管件
| ()
|
| QB/T 2003-1994
| 食品工业用不锈钢对缝焊接管件
| ()
|
| QB/T 2480-2000
| 建筑用硬聚氯乙烯(PVC-U)雨落水管材及管件
| ()
|
| QB/T 3802-1999
| 化工用硬聚氯乙烯管件
| Unplasticized polyvinyl chloride(PVC)fittings for chemical industry
|
| QC/T 669-2000(2005)
| 汽车空调(HFC-134a)用管接头和管件
| ()
|
| SB/T 10355-2002
| 制冷系统和热泵—软管件、隔振器和膨胀接头—要求、设计与安装
| ()
|
| SY/T 0510-1998(2006年确认)
| 钢制对焊管件
| ()
|
| SY/T 0518-2002
| 油气管道钢制对焊管件设计规程
| ()
|
| SY/T 6266-2004
| 低压玻璃纤维管线管和管件
| ()
|
| SY/T 6701-2007
| 增强MC尼龙管和尼龙—钢复合管及管件
| Reinforced MC nylon pipes and nylon-steel composite pipes and fittings
|
| YB/T 177-2000(2006年确认)
| 连续铸造球墨铸铁管
| ()
|
| YS/T 583-2006
| 热锻水暖管件用黄铜棒
| ()
|
| YS/T 584-2006
| 电极材料用铬、锆青铜管件
| ()
|
| 编号 | 中文名称 | 英文名称 |
|---|